Tag Archives: permanent magnet compressor

China wholesaler Permanent Magnet Variable Speed Screw Air Compressor (Ca Series 7.5-75kw) air compressor for sale

Product Description

Product Presentation

CA Series Parameter Table
Model	CA7.5	CA11	CA15	CA22	CA37	CA55	CA75
Rate Power	7.5kW	11kW	15kW	22kW	37kW	55kW	75kW
F.A.D	1.1m3/min	1.6m3/min	2.6m3/min	3.6m3/min	6.5m3/min	10.0m3/min	12.5m3/min
Pressure	≤0.8MPa (Please contact if there is any other pressure requirement,Under different pressure, the exhaust volume can be adjusted)
Drive Type	PM Motor/Direct-driven
Voltage/Frequency	AC380V-50Hz
Starting Mode	Variable Frequency
Connection	G1/2”	G1”		G1”	Rp1-1/2”	G2”	G2”
Size(LxWxH)	954X600X1035mm	1100X720X1180mm		1100X720X1180mm	1280X920X1350mm	1580X1160X1600mm	1580X1160X1600mm
Weight	155kg	245kg		285kg	445kg	920kg	990kg

Comparison between permanent magnet motor and ordinary asynchronous motor

Compared with electrically excited motors, permanent magnet motors have the following advantages:
High efficiency
Eliminate excitation system loss, improve efficiency 5-12%, high power factor, large torque inertia ratio, stator current and stator resistance loss reduction, and rotor parameters can be measured, good control performance, motor direct drive, no speed slip, no bearing and connection transmission, efficiency increased by more than 3%, light load than the same specification asynchronous motor efficiency increased by 15-35% or so. Always efficient regardless of light load or heavy load. At present, the energy efficiency of permanent magnet motors used by Hylein has reached the national level 1 energy efficiency standards.
Low noise
Reasonable magnetic field design, magnetic density distribution, wider operating frequency range, lower operating noise. Truly constant air pressure: open loop vector control, response time < 50ms, can adjust gas production in an instant over a wide range.
Compact structure, small size, light weight, high precision and fast response
The exciting winding and the exciting power supply (magnetic pole core) are eliminated, and the structure is simple, the operation is reliable and the maintenance is convenient.
High starting torque
The starting torque and overload capacity of permanent magnet synchronous motor are 1 power level higher than that of three-phase asynchronous motor, and the ratio of the maximum starting torque to the rated torque can reach more than 3 times, while the general asynchronous motor is only 1.6 times.

Single Stage Compression

Oil cooled machine
Core Ndfeb magnetic steel, not only high temperature 180ºC, and energy efficiency level is higher than IE5. The heat loss is small and the efficiency is high under the same power.

Reliable intake valve system
Unique structural design, reliable intake valve system, do not have to worry about emergency shutdown and sudden power outage oil injection.
The oil and gas pipe of the whole machine are made of stainless steel material or imported hose, which is durable and not aging. It is sealed with thread and flat O-ring, easy to disassemble without leakage.

Rear exhaust design to suck instead of blow
Fans dissipate heat faster and make less noise. The traditional fan blows against the cooler, which has large resistance and loud noise. The back row is cooled, and the cooler is placed vertically to avoid the dust falling on the cooler from the top down, which will lead to slow blockage for a long time. This design avoids.

New oil-cooled motor
Mold forming, no welding points, no risk; Rotary oil passage circulation, small pressure difference; It’s a circular surface; Circular surface type oil passage, full oil flow, uniform cooling oil passage in the outside, easy to repair and maintenance.

Quality Upgrade Three Lightspots

Company Profile

HangZhou Hylein Energy & Environmental Technology Co., Ltd. is located in HangZhou, Pearl River Delta, known as China’s compressor production base, is a professional engaged in all kinds of screw air compressor, nitrogen machine, oxygen generator, vacuum pump, magnetic suspension compressor R & D, production and sales of manufacturing enterprises, with standard production assembly line, the introduction of Europe and North America mature and experienced technology, Focus on providing a full range of services for various industries.
We strictly follow the IS09001 quality system standards and related industry standards, and throughout the product design, procurement, manufacturing, inspection, sales and service of the entire process, we always adhere to the global procurement strategy to ensure the superior performance of each air compressor, we pay attention to the development of new products, the latest energy-saving products are providing quality services for the global industrial energy-saving cause.

Workshop Workshop

After-sales Service

Equipment support High efficiency and energy saving equipment since the start of normal commissioning, to ensure the normal operation of the equipment.

Service scheme Monthly, quarterly regular arrangement of personnel to the user phone or on-site equipment operation inspection, testing work, timely understanding of unit operation dynamics, effective answer to user equipment operation questions, and do the corresponding need to improve maintenance, maintenance, to ensure the long-term effective work of the equipment, while providing service reports every time.

We have a CHINAMFG theoretical knowledge, practical ability of strong service team and high-quality management team.

Our company will provide the fastest solution after receiving the notification of the failure of the user’s equipment, and arrange technicians to arrive at the scene as soon as necessary.

Warranty commitment High efficiency and energy saving equipment since the start of normal commissioning, the whole machine warranty for 1 year.

FAQ

Q1: What’s your delivery time?

O: It takes about 15 days, if there is any urgent order, please contact us.

Q2: How long is your air compressor warranty?

O: One year for the whole machine when the compressor leave our factory.

Q3: How about your after-sales service?

O:1. Provide customers with installation and commissioning online instructions.

2. Well-trained engineers available to overseas service

/* October 22, 2571 15:47:17 */(()=>{function d(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

air compressor

Can air compressors be used for cleaning and blowing dust?

Yes, air compressors can be effectively used for cleaning and blowing dust in various applications. Here’s how air compressors are utilized for these purposes:

1. Cleaning Machinery and Equipment:

Air compressors are commonly used for cleaning machinery and equipment in industries such as manufacturing, automotive, and construction. Compressed air is directed through a nozzle or blowgun attachment to blow away dust, debris, and other contaminants from surfaces, crevices, and hard-to-reach areas. The high-pressure air effectively dislodges and removes accumulated dust, helping to maintain equipment performance and cleanliness.

2. Dusting Surfaces:

Air compressors are also employed for dusting surfaces in various settings, including homes, offices, and workshops. The compressed air can be used to blow dust off furniture, shelves, electronic equipment, and other objects. It provides a quick and efficient method of dusting, especially for intricate or delicate items where traditional dusting methods may be challenging.

3. Cleaning HVAC Systems:

Air compressors are utilized for cleaning HVAC (Heating, Ventilation, and Air Conditioning) systems. The compressed air can be used to blow dust, dirt, and debris from air ducts, vents, and cooling coils. This helps improve the efficiency and air quality of HVAC systems, preventing the buildup of contaminants that can affect indoor air quality.

4. Blowing Dust in Workshops:

In workshops and garages, air compressors are often used to blow dust and debris from workbenches, power tools, and work areas. Compressed air is directed to blow away loose particles and maintain a clean and safe work environment. This is particularly useful in woodworking, metalworking, and other trades where dust and debris can accumulate during the manufacturing or fabrication processes.

5. Cleaning Electronics and Computer Equipment:

Air compressors are employed for cleaning electronics and computer equipment. The compressed air is used to blow dust and debris from keyboards, computer cases, circuit boards, and other electronic components. It helps in preventing overheating and maintaining the proper functioning of sensitive electronic devices.

6. Industrial Cleaning Applications:

Air compressors find extensive use in industrial cleaning applications. They are employed in industrial settings, such as factories and warehouses, for cleaning large surfaces, production lines, and equipment. Compressed air is directed through specialized cleaning attachments or air-operated cleaning systems to remove dust, dirt, and contaminants efficiently.

When using air compressors for cleaning and blowing dust, it is important to follow safety precautions and guidelines. The high-pressure air can cause injury if directed towards the body or sensitive equipment. It is advisable to wear appropriate personal protective equipment, such as safety glasses and gloves, and ensure that the air pressure is regulated to prevent excessive force.

Overall, air compressors provide a versatile and effective solution for cleaning and blowing dust in various applications, offering a convenient alternative to traditional cleaning methods.

air compressor

What is the energy efficiency of modern air compressors?

The energy efficiency of modern air compressors has significantly improved due to advancements in technology and design. Here’s an in-depth look at the energy efficiency features and factors that contribute to the efficiency of modern air compressors:

Variable Speed Drive (VSD) Technology:

Many modern air compressors utilize Variable Speed Drive (VSD) technology, also known as Variable Frequency Drive (VFD). This technology allows the compressor motor to adjust its speed according to the compressed air demand. By matching the motor speed to the required airflow, VSD compressors can avoid excessive energy consumption during periods of low demand, resulting in significant energy savings compared to fixed-speed compressors.

Air Leakage Reduction:

Air leakage is a common issue in compressed air systems and can lead to substantial energy waste. Modern air compressors often feature improved sealing and advanced control systems to minimize air leaks. By reducing air leakage, the compressor can maintain optimal pressure levels more efficiently, resulting in energy savings.

Efficient Motor Design:

The motor of an air compressor plays a crucial role in its energy efficiency. Modern compressors incorporate high-efficiency electric motors that meet or exceed established energy efficiency standards. These motors are designed to minimize energy losses and operate more efficiently, reducing overall power consumption.

Optimized Control Systems:

Advanced control systems are integrated into modern air compressors to optimize their performance and energy consumption. These control systems monitor various parameters, such as air pressure, temperature, and airflow, and adjust compressor operation accordingly. By precisely controlling the compressor’s output to match the demand, these systems ensure efficient and energy-saving operation.

Air Storage and Distribution:

Efficient air storage and distribution systems are essential for minimizing energy losses in compressed air systems. Modern air compressors often include properly sized and insulated air storage tanks and well-designed piping systems that reduce pressure drops and minimize heat transfer. These measures help to maintain a consistent and efficient supply of compressed air throughout the system, reducing energy waste.

Energy Management and Monitoring:

Some modern air compressors feature energy management and monitoring systems that provide real-time data on energy consumption and performance. These systems allow operators to identify energy inefficiencies, optimize compressor settings, and implement energy-saving practices.

It’s important to note that the energy efficiency of an air compressor also depends on factors such as the specific model, size, and application. Manufacturers often provide energy efficiency ratings or specifications for their compressors, which can help in comparing different models and selecting the most efficient option for a particular application.

Overall, modern air compressors incorporate various energy-saving technologies and design elements to enhance their efficiency. Investing in an energy-efficient air compressor not only reduces operational costs but also contributes to sustainability efforts by minimizing energy consumption and reducing carbon emissions.

air compressor

What maintenance is required for air compressors?

Maintaining air compressors is essential to ensure their optimal performance, longevity, and safe operation. Regular maintenance helps prevent breakdowns, improves efficiency, and reduces the risk of accidents. Here are some key maintenance tasks for air compressors:

1. Regular Inspection: Perform visual inspections of the air compressor to identify any signs of wear, damage, or leaks. Inspect the compressor, hoses, fittings, and connections for any abnormalities. Pay attention to oil leaks, loose bolts, and worn-out components.

2. Oil Changes: If your air compressor has an oil lubrication system, regular oil changes are crucial. Follow the manufacturer’s recommendations for the frequency of oil changes and use the recommended oil type. Dirty or degraded oil can impact compressor performance and lead to premature wear.

3. Air Filter Cleaning or Replacement: Clean or replace the air filter regularly to ensure proper air intake and prevent contaminants from entering the compressor. Clogged or dirty filters can restrict airflow and reduce efficiency.

4. Drain Moisture: Air compressors produce moisture as a byproduct of the compression process. Accumulated moisture in the tank can lead to rust and corrosion. Drain the moisture regularly from the tank to prevent damage. Some compressors have automatic drains, while others require manual draining.

5. Belt Inspection and Adjustment: If your compressor has a belt-driven system, inspect the belts for signs of wear, cracks, or tension issues. Adjust or replace the belts as necessary to maintain proper tension and power transmission.

6. Tank Inspection: Inspect the compressor tank for any signs of corrosion, dents, or structural issues. A damaged tank can be hazardous and should be repaired or replaced promptly.

7. Valve Maintenance: Check the safety valves, pressure relief valves, and other valves regularly to ensure they are functioning correctly. Test the valves periodically to verify their proper operation.

8. Motor and Electrical Components: Inspect the motor and electrical components for any signs of damage or overheating. Check electrical connections for tightness and ensure proper grounding.

9. Keep the Area Clean: Maintain a clean and debris-free area around the compressor. Remove any dirt, dust, or obstructions that can hinder the compressor’s performance or cause overheating.

10. Follow Manufacturer’s Guidelines: Always refer to the manufacturer’s manual for specific maintenance instructions and recommended service intervals for your air compressor model. They provide valuable information on maintenance tasks, lubrication requirements, and safety precautions.

Regular maintenance is vital to keep your air compressor in optimal condition and extend its lifespan. It’s also important to note that maintenance requirements may vary depending on the type, size, and usage of the compressor. By following a comprehensive maintenance routine, you can ensure the reliable operation of your air compressor and maximize its efficiency and longevity.

air compressors
editor by lmc 2025-02-25

China Standard 15bar Permanent Magnet Brushless DC Motor Battery Driven Vehicle Mounted DC96V DC72V 110V DC144V DC310V Oil-Free Air Compressor 2HP 1500W with Hot selling

Product Description

Model	BST1100DC	BST1100/15DC
Rated Voltage (V)	DC24V above	DC24V above
Input power(W)	≤900	≤900
Speed (r/min)	≥1700	≥1700
Rated pressure (KPa)	700KPa	1500KPa
Max pressure(KPa)	800KPa	1600KPa
Restart pressure (KPa)	0KPa	0KPa
Rated volume flow (m3/h)	7.0m3/h @700KPa	1.8m3/h @1500KPa
Noise dB(A)	≤75dB(A)	≤75dB(A)
Ambient temperature ºC	-41~40 ºC	-41~40 ºC
Insulation Class	F	F
Cold insulation resistance (MΩ)	≥100MΩ	≥100MΩ
Voltage resistance	500V/50Hz 1min (No breakdown)	500V/50Hz 1min (No breakdown)
Net weight (Kg)	16Kg	16Kg
Installation Dimensions (mm)	246×127 mm( Install foot M8)	246×127 mm( Install foot M8)
External Dimensions (mm)	319×195×290mm	319×195×290mm

Typical application
Respirator (ventilator)	oxygenerator
Disinfectant sprayer	Blood analyzer
Clinical aspirator	Dialysis / hemodialysis
Dental vacuum drying oven	Air suspension system
Vending machines / coffee blenders and coffee machines	Massage chair
Chromatographic analyzer	Teaching instrument platform
On board access control system	Airborne oxygen generator

Why choose CHINAMFG air compressor
1. It saves 10-30% energy than the air compressor produced by ordinary manufacturers.
2. It is widely used in medical oxygen generator and ventilator .
3. A large number of high-speed train and automobile application cases, supporting – 41 to 70 ºC, 0-6000 CHINAMFG above sea level .
4. Medium and high-end quality, with more than 7000 hours of trouble free operation for conventional products and more than 15000 hours of trouble free operation for high-end products.
5. Simple operation, convenient maintenance and remote guidance.
6. Faster delivery time, generally completed within 25 days within 1000 PCs.

Machine Parts

Name: Motor
Brand: COMBESTAIR
Original: China
1.The coil adopts the fine pure copper enameled wire, and the rotor adopts the famous brand silicon steel sheet such as ZheJiang baosteel.
2.The customer can choose the insulation grade B or F motor according to What he wants.
3.The motor has a built-in thermal protector, which can select external heat sensor.
4.Voltage from AC100V ~120V, 200V ~240V, 50Hz / 60Hz, DC6V~200V optional ; AC motor can choose double voltage double frequency ; DC Motor can choose the control of the infinitely variable speed.

Machine Parts

Name: Bearing
Brand: ERB , CHINAMFG , NSK
Original: China ect.
1.Standard products choose the special bearing ‘ERB’ in oil-free compressor, and the environment temperature tolerance from -50ºC to 180 ºC . Ensure no fault operation for 20,000 hours.
2.Customers can select TPI, NSK and other imported bearings according to the working condition.

Machine Parts

Name: Valve plates
Brand: SANDVIK
Original: Sweden
1.Custom the valve steel of Sweden SANDVIK; Good flexibility and long durability.
2.Thickness from 0.08mm to 1.2mm, suitable for maximum pressure from 0.8 MPa to 1.2 MPa.

Machine Parts

Name: Piston ring
Brand: COMBESTAIR-OEM , Saint-Gobain
Original: China , France
1.Using domestic famous brand–Polytetrafluoroethylene composite material; Wear-resistant high temperature; Ensure more than 10,000 hours of service life.
2.High-end products: you can choose the ST.gobain’s piston ring from the American import.

serial number	Code number	Name and specification	Quantity	Material	Note
1	212571109	Fan cover	2	Reinforced nylon 1571
2	212571106	Left fan	1	Reinforced nylon 1571
3	212571101	Left box	1	Die-cast aluminum alloy YL104
4	212571301	Connecting rod	2	Die-cast aluminum alloy YL104
5	212571304	Piston cup	2	PHB filled PTFE
6	212571302	Clamp	2	Die-cast aluminum alloy YL102
7	7050616	Screw of cross head	2	Carbon structural steel of cold heading	M6•16
8	212571501	Air cylinder	2	Thin wall pipe of aluninun alloy 6A02T4
9	17103	Seal ring of Cylinder	2	Silicone rubber
10	212571417	Sealing ring of cylinder cover	2	Silicone rubber
11	212571401	Cylinder head	2	Die-cast aluminum alloy YL102
12	7571525	Screw of inner hexagon Cylinder head	12		M5•25
13	17113	Sealing ring of connecting pipe	4	Silicong rubber
14	212571801	Connecting pipe	2	Aluminum and aluminum alloy connecting rod LY12
15	7100406	Screw of Cross head	4	1Cr13N19	M4•6
16	212571409	Limit block	2	Die-cast aluminum alloy YL102
17	000402.2	Air outlet valve	2	7Cr27 quenching steel belt of The Swedish sandvik
18	212571403	valve	2	Die-cast aluminum alloy YL102
19	212571404	Air inlet valve	2	7Cr27 quenching steel belt of The Swedish sandvik
20	212571406	Metal gasket	2	Stainless steel plate of heat and acidresistance
21	212571107	Right fan	1	Reinforced nylon 1571
22	212571201	Crank	2	Gray castiron H20-40
23	14040	Bearing 6006-2Z	2
24	70305	Tighten screw of inner hexagon flat end	2		M8•8
25	7571520	Screw of inner hexagon Cylinder head	2		M5•20
26	212571102	Right box	1	Die-cast aluminum alloy YL104
27	6P-4	Lead protective ring	1
28	7095712-211	Hexagon head bolt	2	Carbon structural steel of cold heading	M5•152
29	715710-211	Screw of Cross head	2	Carbon structural steel of cold heading	M5•120
30	16602	Light spring washer	4		ø5
31	212571600	Stator	1
32	70305	Lock nut of hexagon flange faces	2
33	212571700	Rotor	1
34	14032	Bearing 6203-2Z	2

FAQ

Q1: Are you factory or trade company?
A1: We are factory.

Q2: What the exactly address of your factory?
A2: Our factory is located in Linbei industrial area No.30 HangZhou City of ZHangZhoug Province, China

Q3: Warranty terms of your machine?
A3: Two years warranty for the machine and technical support according to your needs.

Q4: Will you provide some spare parts of the machines?
A4: Yes, of course.

Q5: How long will you take to arrange production?
A5: Generally, 1000 pcs can be delivered within 25 days

Q6: Can you accept OEM orders?
A6: Yes, with professional design team, OEM orders are highly welcome

Q7:Can you accept non-standard customization?

A7:We have the ability to develop new products and can customize, develop and research according to your requirements

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	Remote Guided Maintenance
Warranty:	2 Years
Principle:	Mixed-Flow Compressor

Samples:	US$ 200/Piece 1 Piece(Min.Order) \| Order Sample

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

How Do Water-Lubricated Air Compressors Contribute to Energy Savings?

Water-lubricated air compressors can contribute to energy savings in several ways, making them an attractive option for industries looking to optimize their energy consumption. Here are the key ways in which water-lubricated compressors help achieve energy efficiency:

Reduced friction and improved efficiency: Water serves as a lubricant in water-lubricated compressors, creating a thin film between moving parts to reduce friction. This reduces the energy losses due to mechanical friction and improves the overall efficiency of the compressor. Compared to oil-lubricated compressors, water-lubricated models can achieve higher mechanical efficiency, translating into energy savings over the compressor’s operational lifetime.
Elimination of oil vapor carryover: Oil-lubricated compressors require oil filtration systems to prevent oil carryover into the compressed air stream. These filtration systems consume energy and can introduce pressure drops. In contrast, water-lubricated compressors eliminate the need for oil filtration, reducing energy consumption associated with filtration equipment and minimizing pressure losses. This leads to improved system efficiency and energy savings.
Improved heat transfer and cooling: Water-lubricated compressors offer enhanced heat transfer capabilities compared to oil-lubricated counterparts. Water has a higher specific heat capacity and thermal conductivity, allowing for more efficient heat dissipation. This results in lower operating temperatures and reduces the energy required for cooling the compressor. By optimizing heat transfer, water-lubricated compressors can minimize energy consumption associated with cooling systems or air conditioning in compressor rooms.
Optimized system design: Water-lubricated compressors often employ advanced system designs that further enhance energy efficiency. For example, they may incorporate variable speed drive (VSD) technology, which adjusts the compressor’s speed and power consumption based on the actual air demand. This eliminates energy waste associated with constant-speed operation and reduces energy consumption during periods of low compressed air demand. Additionally, water-lubricated compressors may feature optimized internal components and improved air flow dynamics, resulting in reduced energy losses and improved overall system efficiency.
Heat recovery opportunities: Water-lubricated compressors can provide opportunities for heat recovery. The heat generated during compression can be captured and utilized for various heating applications within the facility, such as space heating, water heating, or process heating. By harnessing this waste heat, water-lubricated compressors contribute to energy savings by offsetting the need for additional energy sources for heating purposes.

By combining these energy-saving features, water-lubricated air compressors help optimize energy consumption, reduce operational costs, and minimize the environmental impact associated with compressed air systems. Implementing water-lubricated compressors with a comprehensive energy management strategy can result in significant energy savings and improved overall sustainability for industrial operations.

air compressor

How Do You Troubleshoot Common Problems with Water-Lubrication Systems?

When encountering common problems with water-lubrication systems, it is essential to follow a systematic troubleshooting approach. Here’s a detailed explanation of the steps involved in troubleshooting common issues with water-lubrication systems:

Step 1: Identify the Problem:

The first step is to identify the specific problem or symptom that is affecting the water-lubrication system. Common problems may include inadequate lubrication, water leaks, abnormal noises, or reduced system performance. Understanding the specific issue will help in determining the appropriate troubleshooting steps.

Step 2: Check Water Supply:

Verify that there is a proper water supply to the system. Ensure that the water source is connected and flowing adequately. Check for any obstructions or restrictions in the water lines that may be affecting the water flow to the lubrication system.

Step 3: Inspect Water Filters and Strainers:

Water filters and strainers are used in water-lubrication systems to remove debris and impurities from the water. Inspect these filters and strainers for clogs or blockages that may be hindering the water flow. Clean or replace the filters as necessary to ensure proper water filtration.

Step 4: Verify Water Pressure:

Check the water pressure within the system to ensure it falls within the recommended range. Low water pressure can result in inadequate lubrication, while high water pressure can cause leaks or damage to the system. Use a pressure gauge to measure the water pressure and adjust it if necessary according to the manufacturer’s guidelines.

Step 5: Examine Water-Lubrication Components:

Closely inspect the various components of the water-lubrication system, including the water pump, distribution lines, lubrication points, and seals. Look for signs of wear, damage, or misalignment that may be contributing to the problem. Tighten loose connections and replace any damaged or worn-out components as needed.

Step 6: Check for Air in the System:

Air trapped within the water-lubrication system can affect its performance. Bleed the system to remove any trapped air. Follow the manufacturer’s instructions for bleeding air from the system, which typically involves opening specific valves or vents until a steady flow of water is achieved.

Step 7: Inspect Cooling Mechanisms:

Water-lubrication systems often incorporate cooling mechanisms, such as heat exchangers or radiators, to dissipate excess heat. Inspect these cooling components for blockages, corrosion, or leaks that may be compromising their effectiveness. Clean or repair the cooling mechanisms as necessary to ensure proper heat dissipation.

Step 8: Consult Manufacturer Documentation:

If the troubleshooting steps above do not resolve the problem, refer to the manufacturer’s documentation, such as the user manual or technical specifications. These resources may provide specific troubleshooting guidelines, diagnostics, or additional maintenance procedures for the water-lubrication system.

Step 9: Seek Professional Assistance:

If the problem persists or if the troubleshooting steps are beyond your expertise, it is advisable to seek professional assistance. Contact the manufacturer’s technical support or consult a qualified technician with experience in water-lubrication systems. They can provide expert guidance and assistance in resolving complex issues.

By following these troubleshooting steps, you can effectively identify and address common problems encountered in water-lubrication systems, ensuring optimal performance and reliability.

air compressor

What Maintenance Is Required for Water-Lubricated Air Compressors?

Maintaining water-lubricated air compressors involves several key maintenance tasks to ensure their optimal performance and longevity. Here are the maintenance requirements typically associated with water-lubricated air compressors:

Regular water quality checks: It is essential to monitor the quality of the water used for lubrication in the compressor. Regular water analysis helps identify any potential contaminants, such as minerals or impurities, that may affect compressor performance or lead to corrosion. If necessary, appropriate water treatment measures should be taken to maintain the desired water quality.
Drain and flush water systems: Periodically draining and flushing the water systems of the compressor helps remove any sediment, debris, or accumulated contaminants. This prevents blockages, maintains water flow, and ensures the cleanliness of the system.
Inspect and clean filters: Filters in the water system, such as intake filters or water separation filters, should be inspected regularly and cleaned or replaced as needed. Clean filters help maintain proper water flow, prevent clogging, and protect internal components from damage or corrosion.
Check for leaks: Regularly inspect the compressor system for any signs of water leaks. Leaks can lead to water loss, reduced lubrication performance, and potential damage to the compressor components. Any identified leaks should be promptly repaired to maintain the integrity of the system.
Monitor and maintain proper water levels: Ensure that the water levels in the compressor are maintained within the recommended range. Low water levels can result in inadequate lubrication and increased friction, while high water levels may lead to excessive moisture in the system. Regularly check and adjust the water levels as necessary.
Inspect and maintain cooling systems: Water-lubricated compressors often utilize water for cooling purposes. Inspect and maintain the cooling systems, such as heat exchangers or radiators, to ensure proper heat dissipation. Clean any accumulated debris or deposits that may impede cooling efficiency.
Follow manufacturer guidelines: It is crucial to follow the manufacturer’s maintenance guidelines and recommendations specific to the water-lubricated air compressor model being used. These guidelines may include additional maintenance tasks or intervals that are necessary for optimal performance and warranty compliance.

Regular and proactive maintenance of water-lubricated air compressors helps ensure their reliable operation, extends their lifespan, and minimizes the risk of performance issues or component failures. It is advisable to consult the compressor’s documentation and seek guidance from the manufacturer or a qualified technician to establish a comprehensive maintenance routine specific to the equipment.

China Standard 15bar Permanent Magnet Brushless DC Motor Battery Driven Vehicle Mounted DC96V DC72V 110V DC144V DC310V Oil-Free Air Compressor 2HP 1500W with Hot selling
editor by CX 2024-02-19

China Standard 22kw~400kw AC Permanent Magnet Variable Frequency Double Stage CHINAMFG Silent Direct Drive Industrial Screw Air Compressor with CE with Best Sales

Product Description

Product Parameters

Model	Motor Power		Maximum Working Pressure		Free Air Delivery		Air Outlet Pipe Diameter	Weight	Dimensions(LWH)
Model	kW	hp	bar(g)	psig	m³/min	cfm	Air Outlet Pipe Diameter	kg	mm
BG30APMII	22	30	7	102	4.3	152	G1-1/2″	650	150010001350
			8	116	4.1	145
			10	145	3.5	124
			13	189	2.7	95
BG40APMII	30	40	7	102	6.0	212	G1-1/2″	700	150010001350
			8	116	5.9	208
			10	145	4.7	166
			13	189	3.9	138
BG50APMII	37	50	7	102	7.1	251	G1-1/2″	750	150010001350
			8	116	6.9	244
			10	145	5.8	205
			13	189	5.4	191
BG60APMII	45	60	7	102	10.0	353	G2″	1250	210013001650
			8	116	9.5	335
			10	145	7.8	275
			13	189	6.8	240
BG75APMII	55	75	7	102	13.0	459	G2″	1300	210013001650
			8	116	12.5	441
			10	145	9.2	325
			13	189	7.5	265
BG100APMII	75	100	7	102	15.5	547	G2″	1350	210013001650
			8	116	15.2	537
			10	145	12.0	424
			13	189	10.2	360
BG125APMII	90	125	7	102	19.8	699	DN80	2700	250016501900
			8	116	19.5	689
			10	145	15.0	530
			13	189	14.0	494
BG150APMII	110	150	7	102	24.0	848	DN80	2800	250016501900
			8	116	23.0	812
			10	145	19.2	678
			13	189	16.0	565
BG180APMII	132	180	7	102	27.5	971	DN80	3000	250016501900
			8	116	27.0	954
			10	145	23.7	837
			13	189	19.0	671
BG220APMII	160	220	7	102	33.0	1165	DN80	4300	300019001950
			8	116	32.5	1148
			10	145	27.5	971
			13	189	22.5	795
BG250APMII	185	250	7	102	39.0	1377	DN80	4400	300019001950
			8	116	36.0	1271
			10	145	32.0	1130
			13	189	27.5	971
BG270APMII	200	270	7	102	43.5	1536	DN80	5000	360022002200
			8	116	41.0	1448
			10	145	35.5	1254
			13	189	31.5	1112
BG300APMII	220	300	7	102	51.5	1819	DN100	5500	360022002200
			8	116	46.0	1624
			10	145	38.5	1360
			13	189	35.5	1254
BG340APMII	250	340	7	102	54.0	1907	DN100	6000	360022002200
			8	116	51.0	1801
			10	145	45.0	1589
			13	189	38.0	1342
BG380APMII	280	380	7	102	60.0	2119	DN125	6800	400023002300
			8	116	57.0	2013
			10	145	50.0	1766
			13	189	43.0	1519
BG420APMII	315	420	7	102	65.0	2295	DN125	7000	400023002300
			8	116	62.0	2190
			10	145	56.0	1978
			13	189	50.5	1783
BG480APMII	355	480	7	102	75.0	2649	DN150	8500	420022002350
			8	116	73.0	2578
			10	145	64.0	2260
			13	189	55.0	1942
BG540APMII	400	540	7	102	84.0	2966	DN150	9000	420022002350
			8	116	82.0	2896
			10	145	72.0	2543
			13	189	61.0	2154

Company Profile

Wallboge is a high-tech enterprise and is considered 1 of the leading manufacturers of air compressor products in China. Our goal is to provide exceptional customer service coupled with quality products and energy saving solutions.

Wallboge’ s primary businesses focus in following key areas:

Integrated screw air compressor for laser cutting
Permanent magnet variable frequency screw air compressor
Two-stage compression permanent magnet variable frequency screw air compressor
Low pressure two-stage compression permanent magnet variable frequency screw air compressor
Low pressure permanent magnet variable frequency screw air compressor
Water-lubricated oil-free screw air compressor
Fixed speed screw air compressor
Oil-free screw blower
Screw vacuum pump

At Wallboge, we earn our customers’ trust and satisfaction by manufacturing the superior quality compressed air products for all industries. All of our products are designed for reliable performance, easy maintenance, and maximum energy efficiency. CHINAMFG has been exporting to more than 150 countries across the globe.

Wallboge continuously innovates product development and management to meet customers’ demand. The powerful enterprise culture and continuous innovation make CHINAMFG improved rapidly. Wallboge’ s vision is to be a world-renowned high-end energy-saving machinery brand, with sustainable development, constantly improving its own value and sharing it with our customers and staff, committed to continuously satisfying the needs of global companies by providing a full range of industrial air compression solutions.

Certifications

Exhibitions

After Sales Service

1. 24/7 after sales service in different languages.
2. Online instruction for installation and commissioning.
3. On-site instruction for installation and commissioning provided by well-trained engineers or local authorized service center.
4. CHINAMFG agents and after sales service available.

Our Advantages

1. Proven product quality.
2. Factory direct prices.
3. On-time delivery.
4. Prompt technical support in different languages before sales, in sales and after sales.
5. Small orders accepted to check quality first.
6. OEM & ODM service available.

FAQ

Q1: Are you a factory or a trading company?
A1: We are a factory. Please check our Company Profile.

Q2: What is the exact address of your factory?
A2: No. 588, East Tonggang Road, Shaxi Town, HangZhou City, ZheJiang Province, China

Q3: What is your delivery time?
A3: For standard voltage, the delivery time is 15 working days after you confirm the order. For non-standard voltage, please contact our sales to confirm the delivery time.

Q4: What kind of payment terms do you accept?
A4: We accept T/T, L/C at sight.

Q5: How long is the warranty of your air compressor?
A5: 2 years for the whole air compressor except consumable spare parts.

Q6: How long could your air compressor be used?
A6: Generally, more than 10 years.

Q7: What is your MOQ requirement?
A7: 1 unit.

Q8: Can you offer OEM & ODM service?
A8: Yes, with a professional design team, we can offer OEM & ODM service.

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	Engineers Available to Overseas Service.
Warranty:	2 Years
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Structure Type:	Closed Type

Customization:	Available \|

air compressor

What are the energy-saving technologies available for air compressors?

There are several energy-saving technologies available for air compressors that help improve their efficiency and reduce energy consumption. These technologies aim to optimize the operation of air compressors and minimize energy losses. Here are some common energy-saving technologies used:

1. Variable Speed Drive (VSD) Compressors:

VSD compressors are designed to adjust the motor speed according to the compressed air demand. By varying the motor speed, these compressors can match the output to the actual air requirement, resulting in energy savings. VSD compressors are particularly effective in applications with varying air demands, as they can operate at lower speeds during periods of lower demand, reducing energy consumption.

2. Energy-Efficient Motors:

The use of energy-efficient motors in air compressors can contribute to energy savings. High-efficiency motors, such as those with premium efficiency ratings, are designed to minimize energy losses and operate more efficiently than standard motors. By using energy-efficient motors, air compressors can reduce energy consumption and achieve higher overall system efficiency.

3. Heat Recovery Systems:

Air compressors generate a significant amount of heat during operation. Heat recovery systems capture and utilize this wasted heat for other purposes, such as space heating, water heating, or preheating process air or water. By recovering and utilizing the heat, air compressors can provide additional energy savings and improve overall system efficiency.

4. Air Receiver Tanks:

Air receiver tanks are used to store compressed air and provide a buffer during periods of fluctuating demand. By using appropriately sized air receiver tanks, the compressed air system can operate more efficiently. The tanks help reduce the number of starts and stops of the air compressor, allowing it to run at full load for longer periods, which is more energy-efficient than frequent cycling.

5. System Control and Automation:

Implementing advanced control and automation systems can optimize the operation of air compressors. These systems monitor and adjust the compressed air system based on demand, ensuring that only the required amount of air is produced. By maintaining optimal system pressure, minimizing leaks, and reducing unnecessary air production, control and automation systems help achieve energy savings.

6. Leak Detection and Repair:

Air leaks in compressed air systems can lead to significant energy losses. Regular leak detection and repair programs help identify and fix air leaks promptly. By minimizing air leakage, the demand on the air compressor is reduced, resulting in energy savings. Utilizing ultrasonic leak detection devices can help locate and repair leaks more efficiently.

7. System Optimization and Maintenance:

Proper system optimization and routine maintenance are essential for energy savings in air compressors. This includes regular cleaning and replacement of air filters, optimizing air pressure settings, ensuring proper lubrication, and conducting preventive maintenance to keep the system running at peak efficiency.

By implementing these energy-saving technologies and practices, air compressor systems can achieve significant energy efficiency improvements, reduce operational costs, and minimize environmental impact.

air compressor

How does the horsepower of an air compressor affect its capabilities?

The horsepower of an air compressor is a crucial factor that directly impacts its capabilities and performance. Here’s a closer look at how the horsepower rating affects an air compressor:

Power Output:

The horsepower rating of an air compressor indicates its power output or the rate at which it can perform work. Generally, a higher horsepower rating translates to a greater power output, allowing the air compressor to deliver more compressed air per unit of time. This increased power output enables the compressor to operate pneumatic tools and equipment that require higher air pressure or greater airflow.

Air Pressure:

The horsepower of an air compressor is directly related to the air pressure it can generate. Air compressors with higher horsepower ratings have the capacity to produce higher air pressures. This is particularly important when operating tools or machinery that require specific air pressure levels to function optimally. For example, heavy-duty pneumatic tools like jackhammers or impact wrenches may require higher air pressure to deliver the necessary force.

Air Volume:

In addition to air pressure, the horsepower of an air compressor also affects the air volume or airflow it can provide. Higher horsepower compressors can deliver greater volumes of compressed air, measured in cubic feet per minute (CFM). This increased airflow is beneficial when using pneumatic tools that require a continuous supply of compressed air, such as paint sprayers or sandblasters.

Duty Cycle:

The horsepower rating of an air compressor can also influence its duty cycle. The duty cycle refers to the amount of time an air compressor can operate continuously before it needs to rest and cool down. Higher horsepower compressors often have larger and more robust components, allowing them to handle heavier workloads and operate for longer periods without overheating. This is particularly important in demanding applications where continuous and uninterrupted operation is required.

Size and Portability:

It’s worth noting that the horsepower rating can also affect the physical size and portability of an air compressor. Higher horsepower compressors tend to be larger and heavier due to the need for more substantial motors and components to generate the increased power output. This can impact the ease of transportation and maneuverability, especially in portable or mobile applications.

When selecting an air compressor, it is essential to consider the specific requirements of your intended applications. Factors such as desired air pressure, airflow, duty cycle, and portability should be taken into account. It’s important to choose an air compressor with a horsepower rating that aligns with the demands of the tools and equipment you plan to operate, ensuring optimal performance and efficiency.

Consulting the manufacturer’s specifications and guidelines can provide valuable information on how the horsepower rating of an air compressor corresponds to its capabilities and suitability for different tasks.

air compressor

What are the different types of air compressors?

There are several different types of air compressors, each with its own unique design and operating principle. Here’s an overview of the most commonly used types:

1. Reciprocating Air Compressors: Reciprocating air compressors, also known as piston compressors, use one or more pistons driven by a crankshaft to compress air. They operate by drawing air into a cylinder, compressing it with the piston’s up-and-down motion, and discharging the compressed air into a storage tank. Reciprocating compressors are known for their high pressure capabilities and are commonly used in industrial applications.

2. Rotary Screw Air Compressors: Rotary screw air compressors utilize two interlocking screws to compress air. As the male and female screws rotate, the air is trapped between them and gradually compressed as it moves along the screw threads. These compressors are known for their continuous duty cycle, high efficiency, and quiet operation. They are widely used in industrial, commercial, and automotive applications.

3. Centrifugal Air Compressors: Centrifugal air compressors rely on the principle of centrifugal force to compress air. They use a high-speed impeller to accelerate the incoming air and then convert the kinetic energy into pressure energy. Centrifugal compressors are commonly used in large-scale industrial applications that require high volumes of compressed air.

4. Rotary Vane Air Compressors: Rotary vane air compressors employ a rotor with sliding vanes that compress the air. As the rotor rotates, the vanes slide in and out of the rotor, creating compression chambers. Air is drawn in, trapped, and compressed as the vanes move. These compressors are compact, reliable, and suitable for small to medium-sized applications.

5. Axial Flow Air Compressors: Axial flow air compressors are primarily used in specialized applications such as aircraft engines and gas turbines. They utilize a series of rotating and stationary blades to compress air in a continuous flow. Axial flow compressors are known for their high flow rates and are designed for applications that require large volumes of compressed air.

6. Scroll Air Compressors: Scroll air compressors consist of two interlocking spirals or scrolls that compress the air. One spiral remains stationary while the other orbits around it, creating a series of expanding and contracting pockets that compress the air. Scroll compressors are compact, reliable, and commonly used in applications where low noise and oil-free air are required, such as medical and dental equipment.

These are just a few examples of the different types of air compressors available. Each type has its own advantages, capabilities, and ideal applications. The choice of air compressor depends on factors such as required pressure, flow rate, duty cycle, noise level, oil-free operation, and specific application requirements.

China Standard 22kw~400kw AC Permanent Magnet Variable Frequency Double Stage CHINAMFG Silent Direct Drive Industrial Screw Air Compressor with CE with Best Sales
editor by CX 2024-02-17

China supplier permanent magnet inverter oil free air compressor with Hot selling

Product Description

Product Description
1. The most advanced split type design
2. The air end and motor are connected by the coupling, free from the trouble of maintenance.
3. Double screw highly efficient air end design of large rotor, larger compressed capacity,
longer service life with imported CHINAMFG bearings.
4. Permanent magnet motor
The motor is made of the special material of rare-earth permanent magnet, strong magnetic field, large
overload torque and small current while starting and operation,
The special rare-earth permanent magnet with the special design of the rotor, makes the efficiency of the
motor 10%-15% higher than the same horsepower induction motor.
Design of the lower temperature, the raise temperature of the motor<60K, greatly improves the service life
and service factor.
Soft starter by the inverter
Avoiding the strong mechanical shock while starting, prolonging the life of machine, reducing the
maintenance, improving the reliability. So it can save 30% energy.
Our Permanent Magnet inverter screw air compressor Series:

Product details:

Application Fields:

Our Exhibition:

Our service:

1.Pre-sale service:

Act as a good adviser and assistant of clients enable them to get rich and generous returns on their investments.
1.Select equipment model.
2.Design and manufacture products according to client’s special requirement ;
3.Train technical personnel for clients .

2.Services during the sale:

1.Pre-check and accept products ahead of delivery .
2. Help clients to draft solving plans .

3.After-sale services:

Provide considerate services to minimize clients’ worries.
1.Complete After-sales service,professional engineers available to service machinery at home or oversea.
2. 24 hours technical support by e-mail.
3.Other essential technological service.

Contact details:
Company name:HangZhou CHINAMFG Compressor Co.,Ltd
Company address:No.498 YouYi north street,Xihu (West Lake) Dis. district,HangZhou city.
Website:http://compscompressor
Sales manager:Rick Zhang Mobile No.:86~885177632 /* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Vertical
Structure Type:	Closed Type
Installation Type:	Stationary Type

Customization:	Available \|

air compressor

How Do Water-Lubricated Air Compressors Impact Compressed Air Quality?

Water-lubricated air compressors can have an impact on the quality of the compressed air they produce. Here’s a detailed explanation of how water-lubricated air compressors can affect compressed air quality:

Moisture Content:

Condensation: Water-lubricated compressors introduce moisture into the compressed air system. During the compression process, as the air cools downstream, moisture can condense and accumulate. This moisture can lead to issues such as corrosion, rust, and contamination of downstream equipment or processes.
Water Carryover: If the compressor’s water separation mechanisms are not efficient or if there are malfunctions in the water removal systems, water droplets or mist may carry over into the compressed air. This can negatively impact the quality of the compressed air and introduce moisture-related issues downstream.

Contamination:

Oil Contamination: In some water-lubricated compressors, there is a potential for oil to mix with the water used for lubrication. If oil and water emulsify or if there are leaks in the compressor system, oil contamination may occur. Oil-contaminated compressed air can have adverse effects on downstream processes, equipment, and products. It can lead to contamination, reduced performance of pneumatic components, and potential health and safety concerns.
Particulate Contamination: Water-lubricated compressors can introduce particulate matter, such as sediment, debris, or rust, into the compressed air system. This can occur if the water supply or water treatment systems are not adequately filtered or maintained. Particulate contamination can clog or damage pneumatic equipment, affect product quality, and cause operational issues in downstream applications.

Preventive Measures:

Water Separation: Water-lubricated compressors employ various water separation mechanisms to remove moisture from the compressed air. This includes moisture separators, water traps, or coalescing filters that are specifically designed to capture and remove water droplets or mist from the compressed air stream. Regular maintenance and inspection of these separation systems are necessary to ensure their proper functioning.
Air Treatment: Additional air treatment components, such as air dryers or desiccant systems, can be installed downstream of water-lubricated compressors to further reduce moisture content in the compressed air. These systems help to remove moisture that may have carried over from the compressor and ensure that the compressed air meets the required dryness standards for specific applications.
Proper Maintenance: Regular maintenance of water-lubricated compressors is essential to minimize the potential impact on compressed air quality. This includes routine inspection, cleaning, and replacement of filters, lubrication systems, and water separation components. Addressing any leaks, malfunctioning components, or system issues promptly can help maintain the integrity of the compressed air and prevent contamination or excessive moisture levels.

By implementing appropriate water separation mechanisms, air treatment systems, and maintenance practices, the impact of water-lubricated air compressors on compressed air quality can be minimized. It is important to consider the specific requirements of the application and follow industry standards and guidelines to ensure the desired compressed air quality is achieved.

air compressor

What Is the Role of Filtration in Water-Lubricated Air Compressors?

Filtration plays a crucial role in water-lubricated air compressors, serving several important purposes. Here’s a detailed explanation of the role of filtration in water-lubricated air compressors:

Contaminant Removal:

Particle Filtration: Filtration systems in water-lubricated air compressors are designed to remove particles and contaminants from the water. These can include sediment, rust, debris, and other solid particles that may be present in the water supply. Removing these contaminants is essential to prevent blockages, clogging, and damage to the compressor components.
Oil Removal: In some cases, water used in compressors may contain traces of oil or hydrocarbons. Filtration systems can also help remove oil and hydrocarbon contaminants from the water, ensuring that the lubrication system remains clean and effective.

Protection of Components:

Lubrication System: Filtration prevents contaminants from reaching the lubrication system of water-lubricated air compressors. This helps maintain the cleanliness and integrity of the lubricant, ensuring optimal lubrication performance and minimizing wear on the compressor’s moving parts. Clean and filtered water can enhance the efficiency and lifespan of the compressor’s lubrication system.
Heat Exchangers and Cooling Systems: Water-lubricated compressors often rely on heat exchangers and cooling systems to regulate the temperature of the compressed air and the compressor itself. Filtration helps protect these components by preventing the accumulation of debris and contaminants that can hinder heat transfer and reduce the cooling efficiency. Clean water free from particles and contaminants promotes effective heat exchange and cooling.

Prevention of System Fouling:

Scaling and Deposits: Filtration systems also help prevent scaling and deposits that can occur when water with high mineral content or hardness is used. These deposits can accumulate on the internal surfaces of the compressor, heat exchangers, or other components, reducing their efficiency and potentially causing operational issues. By removing impurities and controlling mineral content, filtration minimizes the risk of scaling and deposits.

Extended Equipment Lifespan:

Component Protection: By effectively removing contaminants, filtration systems contribute to the protection and longevity of water-lubricated air compressor components. Clean and filtered water reduces the risk of component wear, corrosion, fouling, and blockages, ultimately extending the lifespan of the compressor and reducing maintenance and replacement costs.

Regular Maintenance and Monitoring:

Filter Replacement: Filtration systems require regular maintenance, including the replacement or cleaning of filters. The frequency of filter replacement depends on factors such as water quality, usage conditions, and the specific requirements of the compressor manufacturer. Regular maintenance ensures that the filtration system continues to effectively remove contaminants and protect the compressor components.
Monitoring Water Quality: Alongside filtration, monitoring the quality of the water used in water-lubricated compressors is essential. This can involve periodic water analysis, measurement of key parameters such as pH or conductivity, and visual inspections. Monitoring helps identify any changes in water quality or potential issues with the filtration system, allowing for timely maintenance or corrective actions.

In summary, filtration plays a critical role in water-lubricated air compressors by removing contaminants, protecting components, preventing system fouling, and extending equipment lifespan. By maintaining clean and filtered water, filtration systems contribute to the efficient operation, reliability, and longevity of water-lubricated compressors.

air compressor

What Maintenance Is Required for Water-Lubricated Air Compressors?

Regular water quality checks: It is essential to monitor the quality of the water used for lubrication in the compressor. Regular water analysis helps identify any potential contaminants, such as minerals or impurities, that may affect compressor performance or lead to corrosion. If necessary, appropriate water treatment measures should be taken to maintain the desired water quality.
Drain and flush water systems: Periodically draining and flushing the water systems of the compressor helps remove any sediment, debris, or accumulated contaminants. This prevents blockages, maintains water flow, and ensures the cleanliness of the system.
Inspect and clean filters: Filters in the water system, such as intake filters or water separation filters, should be inspected regularly and cleaned or replaced as needed. Clean filters help maintain proper water flow, prevent clogging, and protect internal components from damage or corrosion.
Check for leaks: Regularly inspect the compressor system for any signs of water leaks. Leaks can lead to water loss, reduced lubrication performance, and potential damage to the compressor components. Any identified leaks should be promptly repaired to maintain the integrity of the system.
Monitor and maintain proper water levels: Ensure that the water levels in the compressor are maintained within the recommended range. Low water levels can result in inadequate lubrication and increased friction, while high water levels may lead to excessive moisture in the system. Regularly check and adjust the water levels as necessary.
Inspect and maintain cooling systems: Water-lubricated compressors often utilize water for cooling purposes. Inspect and maintain the cooling systems, such as heat exchangers or radiators, to ensure proper heat dissipation. Clean any accumulated debris or deposits that may impede cooling efficiency.
Follow manufacturer guidelines: It is crucial to follow the manufacturer’s maintenance guidelines and recommendations specific to the water-lubricated air compressor model being used. These guidelines may include additional maintenance tasks or intervals that are necessary for optimal performance and warranty compliance.

China supplier permanent magnet inverter oil free air compressor with Hot selling
editor by CX 2024-02-04

China factory 2 Bar 3 Bar 4 Bar 5 Bar Low-Pressure Water-Injection Oil-Free Single Screw Type Air Compressors with Permanent Magnet Motor air compressor CHINAMFG freight

Product Description

LG-II series two-stage air compressor

Product Description

Main Machine:

Adopt two-stage compression main engine, large rotor and low speed.
The upper and lower integrated design concept combines the first-stage compression rotor and the second-stage compression rotor in 1 casing to achieve the highest compression transfer efficiency.

3. The compression ratio of each stage is small, the leakage is smaller, and the volume utilization rate is high. The bearing is less stressed and has a long service life.

Intake system:
Vertical straight-through air intake structure minimizes pressure loss, special air inlet sealing material ensures long service life, no wearing parts, reliable performance and long service life.

Piping system:
The pipeline system adopts the American standard pipeline design. Due to the large inner diameter of the transport pipe and the small flow resistance, the hard pipe usually has a higher transport rate than the hose, and is stable, long service life, and maintenance-free for life.

Permanent magnet motor:
The variable frequency permanent magnet motor has the characteristics of high efficiency, high power factor, wide high efficiency interval, stable speed, zero slip, and energy saving. Therefore, the permanent magnet frequency conversion equipment under the two-stage CHINAMFG can be more energy saving.

Controller:

Adopt advanced microcomputer control to achieve intelligent operation and humanized operation, and the operation status is clear at a glance.

2. Equipped with advanced intelligent control system, various parameters such as pressure and temperature are continuously monitored, controlled and displayed according to preset values.
3. It has the function of automatic fault alarm and protection, and stores historical operation records in time.

Product Feature
Energy saving analysis

The compression ratio of each stage is much smaller than the compression ratio of the common main engine of the same power, and by oil injection cooling, the temperature of the secondary intake air is reduced, and the compression work is greatly reduced.
The low pressure ratio greatly reduces the backflow leakage between the rotors, and greatly improves the volumetric efficiency and adiabatic efficiency, which is ultimately reflected in the increase in the compressed gas production.
Two-stage compression is better than single-stage at the same power.

Specification

Mode		L571A-11	L030A-11	L037A-11
Machine Set	Exhaust volume (m³/min)	4.2	6.2	7.2
	Exhaust pressure (MPa)	0.8	0.8	0.8
	Compression level	2	2	2
	Motor power(kw)	22	30	37
	Motor speed(rpm)	1480	1480	1480
	Energy efficiency rating	Grade I	Grade I	Grade I
	Start method	soft start	soft start	soft start
	Transmission mode	direct connection	direct connection	direct connection
	Connection size	G1-1/2″	G1-1/2″	G1-1/2″
	Cooling method	air cooling	air cooling	air cooling
	Length(mm)	1785	1785	1785
	Width(mm)	1107	1107	1107
	Height(mm)	1432	1432	1432
	Machine weight(kg)	1200	1300	1350

Mode		L045A-11	L055A-11	L075A-11
Machine Set	Discharge volume(m3/min)	10.5	12.55	15.5
	Discharge pressure (MPa)	0.8	0.8	0.8
	Compression level	2	2	2
	Motor power(kw)	45	55	75
	Motor speed(rpm)	1480	1480	1480
	Energy efficiency rating	Grade I	Grade I	Grade I
	Start method	soft start	soft start	soft start
	Transmission mode	direct connection	direct connection	direct connection
	Connection size	G1-1/2″	G2″	G2″
	Cooling method	air cooling	air cooling	air cooling
	Length(mm)	1785	2180	2180
	Width(mm)	1107	1350	1350
	Height(mm)	1432	1600	1600
	Machine weight(kg)	1850	2000	2150

FAQ

Q1: What’s your delivery time?
A: 15 days to produce, within 3 days if in stock.

Q2: What’s methods of payments are accepted?
A: We agree T/T ,L/C , West Union ,Money Gram ,Paypal.

Q3: What about the shipments and package?
A: 40′ container for 2 sets, 20′ container for 1 set,
Machine in nude packing, spare parts in standard export wooden box.

Q4: Have you got any certificate?
A:We have got ISO,CE certificate.

Q5: How to control the quality?
A: We will control the quality by ISO and CE requests.

Q6: Do you have after-sale service and warranty service ?
A: Yes, we have.We can supply instruction for operation and maintenance.If necessary, we can send our engineer to repair the machine in your company.
Warranty is 1 year for the machine.

Q7: Can I trust your company ?
A: Our company has been certificated by Chinese government,and verified by SGS Inspection Company.

/* March 10, 2571 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

After-sales Service:	Online
Warranty:	3000hours
Lubrication Style:	Lubricated

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

What Is the Role of Water Separators in Water-Lubricated Compressors?

In water-lubricated compressors, water separators play a crucial role in maintaining the integrity and performance of the compressed air system. Here’s a detailed explanation of their role:

Water separators, also known as moisture separators or condensate separators, are components within the compressed air system that are specifically designed to remove water or moisture from the compressed air stream. They help ensure that the compressed air remains dry and free from excessive moisture, which can cause various issues in the system and downstream equipment.

The primary role of water separators in water-lubricated compressors is to separate and remove water that is present in the compressed air due to the compression process and condensation. Here’s how they accomplish this:

Condensate Separation: During the compression of air, moisture present in the air is compressed along with the air molecules. As the compressed air cools down after the compression stage, the moisture condenses into liquid form. Water separators are designed to efficiently separate this condensate from the compressed air stream, preventing it from entering downstream equipment, pipelines, or end-use applications.
Gravity and Centrifugal Separation: Water separators utilize various separation principles to separate the condensate from the compressed air. Gravity-based separators rely on the difference in density between the water droplets and the compressed air to allow the water to settle at the bottom of the separator, where it can be drained out. Centrifugal separators use centrifugal force to spin the air and water mixture, causing the water droplets to be thrown outwards and collected in a separate chamber.
Coalescing and Filtration: Water separators often incorporate coalescing and filtration mechanisms to enhance their efficiency. Coalescing filters are used to capture and merge small water droplets into larger droplets, making it easier for the separator to separate them from the compressed air. Filtration elements, such as fine mesh or media, may be incorporated to remove any remaining water droplets or particulate matter that could potentially pass through the separator.
Automatic Drainage: To ensure continuous and efficient operation, water separators are equipped with automatic drain valves. These valves periodically or on demand, expel the collected condensate from the separator. Automatic drainage prevents the accumulation of water in the separator, which can lead to reduced separation efficiency, increased pressure drop, and potential damage to downstream equipment.

By effectively removing water and moisture from the compressed air stream, water separators help prevent issues such as corrosion, clogging, freezing, and degradation of pneumatic equipment and processes. They contribute to maintaining the quality and reliability of the compressed air system while protecting downstream components and applications from the negative effects of moisture.

It is important to note that proper sizing, installation, and maintenance of water separators are essential to ensure their optimal performance. Regular inspection and maintenance of the separators, including draining the collected condensate, replacing filtration elements, and checking for any leaks or malfunctions, are necessary to ensure the efficient operation of water-lubricated compressors and the overall compressed air system.

air compressor

Are There Any Restrictions on the Type of Water Used in Water-Lubricated Compressors?

When it comes to water-lubricated compressors, there are certain restrictions and considerations regarding the type of water that can be used. Here’s a detailed explanation of the restrictions on the type of water used in water-lubricated compressors:

Water Quality:

Cleanliness: The water used in water-lubricated compressors should be clean and free from excessive impurities or contaminants. Impurities like sediment, minerals, or debris can cause blockages, wear, or damage to the compressor components. It is important to use water that meets the cleanliness requirements specified by the manufacturer.
Chemical Composition: The chemical composition of the water can also be a factor to consider. Water with high mineral content or hardness can lead to scale formation, which can affect the performance and lifespan of the compressor. Water treatment methods, such as water softening or filtration, may be necessary to maintain the desired water quality.

Water Temperature:

Freezing Point: In cold climates, it is important to ensure that the water used in the compressor’s lubrication system does not freeze. Freezing can cause operational issues and damage to the equipment. The water temperature should be maintained above freezing point through insulation, heating, or other suitable methods.
Temperature Range: Water-lubricated compressors may have specific temperature requirements to ensure optimal operation and lubrication. Operating the compressor with water temperatures outside the recommended range can affect its performance and lifespan. It is important to adhere to the manufacturer’s guidelines regarding the acceptable temperature range for the water used.

Water Treatment:

Water Treatment Systems: Depending on the quality of the available water supply, it may be necessary to use water treatment systems to ensure the water meets the required standards. Water treatment systems can help remove impurities, control chemical composition, and maintain the desired water quality for effective lubrication and cooling.
Water Treatment Frequency: Regular maintenance and monitoring of the water treatment systems are essential to ensure their effectiveness. The frequency of water treatment, such as filtration or chemical treatment, may vary depending on the specific conditions and the water quality in the area.

Manufacturer Recommendations:

Consulting the Manufacturer: It is important to consult the manufacturer’s guidelines and recommendations regarding the type of water to be used in water-lubricated compressors. Manufacturers may specify the acceptable water quality parameters, treatment methods, or restrictions to ensure optimal performance and longevity of the compressor.

By considering the cleanliness, chemical composition, temperature, and appropriate water treatment measures, the type of water used in water-lubricated compressors can be optimized to meet the requirements specified by the manufacturer. Adhering to these restrictions helps ensure efficient and reliable operation of the compressor while minimizing the risk of component damage or performance issues.

air compressor

Are Water-Lubricated Air Compressors Suitable for Food and Beverage Industries?

Water-lubricated air compressors can be highly suitable for the food and beverage industries due to several reasons:

Food-grade lubrication: Water is a natural and food-grade lubricant. It does not introduce harmful contaminants or chemicals into the production process, ensuring the safety and quality of food and beverage products. Water lubrication eliminates the risk of oil contamination in food products that can occur with oil-lubricated compressors.
Compliance with hygiene standards: The food and beverage industries have strict hygiene standards and regulations. Water-lubricated air compressors align with these standards as water is a clean and sanitary lubricant. It minimizes the risk of cross-contamination and helps maintain a hygienic production environment.
Reduced risk of product contamination: Water lubrication eliminates the possibility of oil carryover or oil vapor entering the compressed air system. This reduces the risk of oil contamination in food and beverage products, ensuring their purity and quality.
Improved product shelf life: Oil-lubricated compressors can release oil aerosols or vapors that may negatively affect the taste, odor, or quality of food and beverage products. Water-lubricated compressors eliminate this concern, contributing to improved product shelf life and maintaining the desired sensory attributes.
Easy cleanup and maintenance: Water lubrication simplifies cleanup and maintenance procedures in food and beverage production facilities. Water does not leave behind sticky residues or require extensive cleaning processes. It facilitates faster and more efficient cleaning, reducing downtime and improving overall productivity.
Environmental friendliness: Water is a sustainable and environmentally friendly lubricant choice. It is non-toxic, biodegradable, and does not contribute to air or water pollution. Using water-lubricated air compressors aligns with the sustainability goals of the food and beverage industries.

Considering these factors, water-lubricated air compressors are well-suited for the food and beverage industries, ensuring compliance with hygiene standards, preventing product contamination, and promoting a safe and sustainable production environment.

China factory 2 Bar 3 Bar 4 Bar 5 Bar Low-Pressure Water-Injection Oil-Free Single Screw Type Air Compressors with Permanent Magnet Motor air compressor CHINAMFG freight
editor by CX 2023-12-28

China factory CHINAMFG Oil Lubricated Rotary Twin Portable Air CHINAMFG Permanent Magnet Fixed Speed Direct Drive Oil Free Air Compressor air compressor lowes

Product Description

REDUCE ENERGY CONSUMPTION

Under different conditions,the demand for gas will float.Through a large number of research and calculation of marketdemandCha nun confirmed it.Only about 10% of applications require stable air supplyTherefore,frequency conversioncompressor can play a greater role in energy saving.
Energy cost often accounts for 70% of the life cycle cost of a compressor. The production of compressed air may account for 40% of all electricity costs in the plant.In almost every factory,the gas consumption will vary with different time periods,with its high and low CHINAMFG periods. permanent magnet variable frequency screw air compressor can supply glass completely according to the requirements of gas consumption,which can not only save a lot of energy, but also protect theenvironment for future generations.
INTERIOR STRUCTURE

CUSTOM OIL
COOLED MOTOR
First-stage energy-efficient motor,Low Noise,IP65 protection grade

AUTOMOTIVE GRADE
PERMANENT MAGNET MOTOR
IE4 high efficiency permanent magnet motor.
AUTOMOTIVE PERMANENT MAGNET MOTOR ForN38UH high grade permanent magnet, IP67 protection grade, and fully enclosed structure uniquevacuum epoxy dipping paint,effectively guaranteeing the stable operation of unit.

CHANUN
CUSTOM CONVERTER
Permanent magnet variable-frequency conversion technology, wide voltage. energy-saving ,with a small impact on the power grid.

7 INCH TOUCH SCREEN

Large touch screen.all-round protection monitoring with functions of motor start/stopcontrol, operation control:reversal protection of air compressor: and multi-point temperature detection and control protection.

HIGH MOBILITY (OPTIONAL)

Easy and flexible to rotate. so that the air compressor is able to move conveniently andquickly (optional)

ZheJiang CHINAMFG Machinery Manufacturing Co. , Ltd. is located in HangZhou, ZheJiang .CHINAMFG is a comprehensive screw air compressor manufacturer that engaged in R & D, design, production and sales. It has a plant of 20,000 square meters, including a large production workshop,a comprehensive first-class exhibition hall and a testing laboratory.

Dukas has excellent mechanical engineering designers, an experienced staff team and a professional management team. The production concept focuses on energy-saving and is committed to perfecting and improving the technological process in order to get the core technology of super frequency energy-saving, achieving the characteristics of mute, durability, power saving and safety.

The company has 9 series of products with multiple models. Including Fixed speed air compressor, PM VSD air compressor, PM VSD two-stage air compressor, 4-in-1 air compressor, Oil free water lubrcating air compressor, Diesel portable screw air compressor, Electric portable screw air compressor, Air dryer, Adsorption machine and the matching spare parts.

Dukas adheres to the business philosophy of cooperation and mutual benefit to provide a one-stop service for every customer!

Dukas air compressors not only cover the domestic market but also are exported to more than 20 countries and regions such as South Africa, Australia, Thailand, Russia, Argentina, Canada and so on.
Dukas products have won a good reputation from users for their excellent quality and style. The company has always adhered to the concept of quality first, service first and dedication to providing every customer with excellent products and meticulous after-sales service!

Dukas warmly welcome customers to visit our factory and establish a wide range of cooperation!

Frequency Asked Question:

Q1: Are you factory or trade company?
A1: We are factory.

Q2: What the exactly address of your factory?
A2: Our Factory is Located in Xihu (West Lake) Dis. County, HangZhou City, ZheJiang Province, China.

Q3: Will you provide spare parts of your products?
A3: Yes, We provide all parts to customer, so you can do repair or maintenance without trouble.

Q4: Can you accept OEM orders?
A4: Yes, with professional design team, OEM orders are highly welcome.

Q5: How long will you take to arrange production?
A5: Immediate delivery for stock products.380V 50HZ we can delivery the goods within 3-15 days. Other voltage or other color we will delivery within 25-30 days.

Q6: Warranty terms of your machine?
A6: Two years warranty for the machine and technical support always according to your needs.

Q7: Can you provide the best price?
A7:According to your order, we will provide you the best price.

After-sales Service:	24 Hours
Warranty:	2 Year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Horizontal

Customization:	Available \|

air compressor

Can Water-Lubricated Compressors Be Used in High-Pressure Applications?

Water-lubricated compressors can be used in high-pressure applications, but there are certain considerations and limitations to keep in mind. Here’s a detailed explanation:

Water-lubricated compressors are typically designed for lower to medium-pressure ranges. They are commonly used in applications where the required discharge pressure does not exceed a certain threshold, typically up to a few hundred pounds per square inch (psi). However, there are specialized water-lubricated compressors available that can handle higher pressures, depending on the specific design and construction.

The ability of a water-lubricated compressor to operate at high pressures depends on several factors:

Compressor Design: The design and construction of the compressor play a crucial role in determining its maximum pressure rating. Compressors designed for high-pressure applications need to have robust components, such as reinforced casings, high-strength materials, and proper sealing mechanisms to withstand the elevated pressures. Special attention should be given to the design of the water-lubricated bearing system to ensure it can handle the increased loads and pressures.
Water Supply and Cooling: High-pressure compressors generate more heat during the compression process, requiring efficient cooling mechanisms to maintain safe operating temperatures. Sufficient water supply and cooling capacity must be available to handle the increased heat load. Adequate flow rates, temperature control, and cooling methods, such as water jackets or external cooling systems, may be necessary to prevent overheating and ensure proper lubrication and cooling of the compressor components.
Water Quality: The quality of the water used for lubrication becomes even more critical in high-pressure applications. Any impurities, contaminants, or minerals present in the water can cause increased wear, corrosion, or blockages, jeopardizing the compressor’s performance and reliability. Water treatment or filtration systems may be required to maintain the desired water quality and prevent damage to the compressor.
Sealing and Leakage Control: As the pressure increases, it becomes more challenging to maintain effective sealing and prevent leakage in the compressor system. Proper sealing mechanisms, such as high-quality seals and gaskets, are essential to ensure minimal leakage and maintain the required pressure levels. Adequate monitoring and maintenance of the sealing components are necessary to prevent energy losses and ensure the compressor’s efficiency.

It’s worth noting that for extremely high-pressure applications, water-lubricated compressors may not be the most suitable choice. In such cases, alternative lubrication methods, such as oil or specialized lubricants, are often preferred to handle the extreme pressures and provide adequate lubrication and cooling.

When considering the use of water-lubricated compressors in high-pressure applications, it is crucial to consult with the compressor manufacturer or a qualified engineer to ensure that the chosen compressor model is specifically designed and rated for the desired pressure range. Proper installation, maintenance, and adherence to the manufacturer’s guidelines are essential to ensure the safe and efficient operation of the compressor in high-pressure conditions.

air compressor

Are There Any Restrictions on the Type of Water Used in Water-Lubricated Compressors?

Water Quality:

Cleanliness: The water used in water-lubricated compressors should be clean and free from excessive impurities or contaminants. Impurities like sediment, minerals, or debris can cause blockages, wear, or damage to the compressor components. It is important to use water that meets the cleanliness requirements specified by the manufacturer.
Chemical Composition: The chemical composition of the water can also be a factor to consider. Water with high mineral content or hardness can lead to scale formation, which can affect the performance and lifespan of the compressor. Water treatment methods, such as water softening or filtration, may be necessary to maintain the desired water quality.

Water Temperature:

Freezing Point: In cold climates, it is important to ensure that the water used in the compressor’s lubrication system does not freeze. Freezing can cause operational issues and damage to the equipment. The water temperature should be maintained above freezing point through insulation, heating, or other suitable methods.
Temperature Range: Water-lubricated compressors may have specific temperature requirements to ensure optimal operation and lubrication. Operating the compressor with water temperatures outside the recommended range can affect its performance and lifespan. It is important to adhere to the manufacturer’s guidelines regarding the acceptable temperature range for the water used.

Water Treatment:

Water Treatment Systems: Depending on the quality of the available water supply, it may be necessary to use water treatment systems to ensure the water meets the required standards. Water treatment systems can help remove impurities, control chemical composition, and maintain the desired water quality for effective lubrication and cooling.
Water Treatment Frequency: Regular maintenance and monitoring of the water treatment systems are essential to ensure their effectiveness. The frequency of water treatment, such as filtration or chemical treatment, may vary depending on the specific conditions and the water quality in the area.

Manufacturer Recommendations:

Consulting the Manufacturer: It is important to consult the manufacturer’s guidelines and recommendations regarding the type of water to be used in water-lubricated compressors. Manufacturers may specify the acceptable water quality parameters, treatment methods, or restrictions to ensure optimal performance and longevity of the compressor.

air compressor

How Do Water-Lubricated Air Compressors Compare to Oil-Lubricated Ones?

Water-lubricated air compressors and oil-lubricated air compressors have distinct differences in terms of lubrication method, performance, maintenance, and environmental impact. Here is a detailed comparison between the two:

	Water-Lubricated Air Compressors	Oil-Lubricated Air Compressors
Lubrication Method	Water is used as the lubricant in water-lubricated compressors. It provides lubrication and heat dissipation.	Oil is used as the lubricant in oil-lubricated compressors. It provides lubrication, sealing, and heat dissipation.
Performance	Water lubrication offers efficient heat dissipation and cooling properties. It can effectively remove heat generated during compressor operation, preventing overheating and prolonging the compressor’s lifespan. Water lubrication can be suitable for applications where high heat generation is a concern.	Oil lubrication provides excellent lubrication properties, ensuring smooth operation and reduced friction. It offers good sealing capabilities, preventing air leakage. Oil-lubricated compressors are often preferred for heavy-duty applications that require high pressure and continuous operation.
Maintenance	Water lubrication generally requires less maintenance compared to oil lubrication. Water does not leave sticky residues or deposits, simplifying the cleaning process and reducing the frequency of lubricant changes. However, water lubrication may require additional measures to prevent corrosion and ensure proper water quality.	Oil lubrication typically requires more maintenance. Regular oil changes, filter replacements, and monitoring of oil levels are necessary. Contaminants, such as dirt or moisture, can adversely affect oil lubrication and require more frequent maintenance tasks.
Environmental Impact	Water lubrication is more environmentally friendly compared to oil lubrication. Water is non-toxic, biodegradable, and does not contribute to air or water pollution. It has a lower environmental impact and reduces the risk of contamination in case of leaks or spills.	Oil lubrication can have environmental implications. Oil leaks or spills can contaminate the environment, including air, soil, and water sources. Used oil disposal requires proper handling to prevent pollution. Oil-lubricated compressors also release volatile organic compounds (VOCs) into the air, contributing to air pollution.

In summary, water-lubricated air compressors excel in efficient heat dissipation, require less maintenance, and have a lower environmental impact. On the other hand, oil-lubricated air compressors offer excellent lubrication properties and are suitable for heavy-duty applications. The choice between water and oil lubrication depends on specific requirements, operating conditions, and environmental considerations.

China factory CHINAMFG Oil Lubricated Rotary Twin Portable Air CHINAMFG Permanent Magnet Fixed Speed Direct Drive Oil Free Air Compressor air compressor lowes
editor by CX 2023-12-14

China OEM Low Noise 70kw 100HP Permanent Magnet VSD Frequency Conversion Screw Air Compressor mini air compressor

Product Description

Product Features
1. Permanent magnet variable frequency motor Automatic control of power consumption, energy-saving control can greatly reduce operating costs
2. Efficient intake valve. Large diameter, low pressure drop, improve performance and stability, ensure effective regulation and control of flow during start-up, operation, and shutdown stages
3. Cooling system. High heat dissipation efficiency, that the air compressor can run continuously in high temperature and high humidity environment
4. Oil and gas separator. Grade water and oil removal filter Electronic drain valve,automatic mandatory drainage, good water removal effect
Product Parameter

Model	M-100A
Power	75KW 100HP
Working Pressure	125PSI/8.6bar
Cooling	Air Colding
Electric Motor	Permanent Magnet
Voltage	230V 3P 60HZ
Protection Level	IP54
Discharge Temperature	≤ambient +8 ºC
Noise	≤72dB
Air Outlet Size	G2″
Size	200011201590mm
Weight	1070kg

FAQ
1.Who we are?

A:We are based in ZheJiang , China, start from 2011,sell to Southeast Asia(20.00%),Eastern Europe(20.00%), WesternEurope(10.00%), North America(10.00%), Northern Europe(5.00%), Central America(5.00%),SouthAmerica(5.00%),Eastern Asia(5.00%),South Asia(5.00%),Oceania(5.00%),Southern Europe(5.00%),Africa(3.00%),MidEast(2.00%). There are total about 11-50 people in our office.

2.Which payment terms you can accept?

A: We can accept flexible payment include Bank Transfer, LC, DP, West Union, Paypal, or Combination terms as negotiation.

3.Which shipping way can you provide?

A: We can provide shipping by sea, by air , by express and etc according to customer requirements.

4.How to place order?

A: When you are ready to order, please contact us for confirm the suitable solution & plan & model. What cannot be ignored is you should provide a copy purchase order to ensure that your order is processed properly. 5.Do you have an inspection procedure for the product? A: Yes, We have a strict inspection of product qualityand packing.

After-sales Service:	Online Support
Warranty:	1year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Vertical

Customization:	Available \|

air compressor

What is the role of air compressors in power generation?

Air compressors play a significant role in power generation, supporting various operations and equipment within the industry. Here are some key roles of air compressors in power generation:

1. Combustion Air Supply:

Air compressors are used to supply compressed air for the combustion process in power generation. In fossil fuel power plants, such as coal-fired or natural gas power plants, compressed air is required to deliver a steady flow of air to the burners. The compressed air helps in the efficient combustion of fuel, enhancing the overall performance and energy output of the power plant.

2. Instrumentation and Control:

Air compressors are utilized for instrumentation and control systems in power generation facilities. Compressed air is used to operate pneumatic control valves, actuators, and other pneumatic devices that regulate the flow of steam, water, and gases within the power plant. The reliable and precise control provided by compressed air ensures efficient and safe operation of various processes and equipment.

3. Cooling and Ventilation:

In power generation, air compressors are involved in cooling and ventilation applications. Compressed air is used to drive air-operated cooling fans and blowers, providing adequate airflow for cooling critical components such as generators, transformers, and power electronics. The compressed air also assists in maintaining proper ventilation in control rooms, substations, and other enclosed spaces, helping to dissipate heat and ensure a comfortable working environment.

4. Cleaning and Maintenance:

Air compressors are employed for cleaning and maintenance tasks in power generation facilities. Compressed air is utilized to blow away dust, dirt, and debris from equipment, machinery, and electrical panels. It helps in maintaining the cleanliness and optimal performance of various components, reducing the risk of equipment failure and improving overall reliability.

5. Pneumatic Tools and Equipment:

In power generation plants, air compressors provide the necessary compressed air for operating pneumatic tools and equipment. These tools include impact wrenches, pneumatic drills, grinders, and sandblasting equipment, which are utilized for installation, maintenance, and repair tasks. The high-pressure air generated by compressors enables efficient and reliable operation of these tools, enhancing productivity and reducing manual effort.

6. Nitrogen Generation:

Sometimes, air compressors are used in power generation for nitrogen generation. Compressed air is passed through a nitrogen generator system, which separates nitrogen from other components of air, producing a high-purity nitrogen gas stream. Nitrogen is commonly used in power plant applications, such as purging systems, blanketing in transformers, and generator cooling, due to its inert properties and low moisture content.

7. Start-up and Emergency Systems:

Air compressors are an integral part of start-up and emergency systems in power generation. Compressed air is utilized to power pneumatic starters for gas turbines, providing the initial rotation needed to start the turbine. In emergency situations, compressed air is also used to actuate emergency shutdown valves, safety systems, and fire suppression equipment, ensuring the safe operation and protection of the power plant.

Overall, air compressors contribute to the efficient and reliable operation of power generation facilities, supporting combustion processes, control systems, cooling, cleaning, and various other applications critical to the power generation industry.

air compressor

Can air compressors be used for medical and dental applications?

Yes, air compressors can be used for various medical and dental applications. Compressed air is a reliable and versatile utility in healthcare settings, providing power for numerous devices and procedures. Here are some common applications of air compressors in medical and dental fields:

1. Dental Tools:

Air compressors power a wide range of dental tools and equipment, such as dental handpieces, air syringes, air scalers, and air abrasion devices. These tools rely on compressed air to generate the necessary force and airflow for effective dental procedures.

2. Medical Devices:

Compressed air is used in various medical devices and equipment. For example, ventilators and anesthesia machines utilize compressed air to deliver oxygen and other gases to patients. Nebulizers, used for respiratory treatments, also rely on compressed air to convert liquid medications into a fine mist for inhalation.

3. Laboratory Applications:

Air compressors are used in medical and dental laboratories for various purposes. They power laboratory instruments, such as air-driven centrifuges and sample preparation equipment. Compressed air is also used for pneumatic controls and automation systems in lab equipment.

4. Surgical Tools:

In surgical settings, compressed air is employed to power specialized surgical tools. High-speed air-driven surgical drills, saws, and bone-cutting instruments are commonly used in orthopedic and maxillofacial procedures. Compressed air ensures precise control and efficiency during surgical interventions.

5. Sterilization and Autoclaves:

Compressed air is essential for operating sterilization equipment and autoclaves. Autoclaves use steam generated by compressed air to sterilize medical instruments, equipment, and supplies. The pressurized steam provides effective disinfection and ensures compliance with rigorous hygiene standards.

6. Dental Air Compressors:

Specialized dental air compressors are designed specifically for dental applications. These compressors have features such as moisture separators, filters, and noise reduction mechanisms to meet the specific requirements of dental practices.

7. Air Quality Standards:

In medical and dental applications, maintaining air quality is crucial. Compressed air used in healthcare settings must meet specific purity standards. This often requires the use of air treatment systems, such as filters, dryers, and condensate management, to ensure the removal of contaminants and moisture.

8. Compliance and Regulations:

Medical and dental facilities must comply with applicable regulations and guidelines regarding the use of compressed air. These regulations may include requirements for air quality, maintenance and testing procedures, and documentation of system performance.

It is important to note that medical and dental applications have specific requirements and standards. Therefore, it is essential to choose air compressors and associated equipment that meet the necessary specifications and comply with industry regulations.

air compressor

What is the purpose of an air compressor?

An air compressor serves the purpose of converting power, typically from an electric motor or an engine, into potential energy stored in compressed air. It achieves this by compressing and pressurizing air, which can then be used for various applications. Here’s a detailed explanation of the purpose of an air compressor:

1. Powering Pneumatic Tools: One of the primary uses of an air compressor is to power pneumatic tools. Compressed air can be used to operate a wide range of tools, such as impact wrenches, nail guns, paint sprayers, sanders, and drills. The compressed air provides the necessary force and energy to drive these tools, making them efficient and versatile.

2. Supplying Clean and Dry Air: Air compressors are often used to supply clean and dry compressed air for various industrial processes. Many manufacturing and production operations require a reliable source of compressed air that is free from moisture, oil, and other contaminants. Air compressors equipped with appropriate filters and dryers can deliver high-quality compressed air for applications such as instrumentation, control systems, and pneumatic machinery.

3. Inflating Tires and Sports Equipment: Air compressors are commonly used for inflating tires, whether it’s for vehicles, bicycles, or sports equipment. They provide a convenient and efficient method for quickly filling tires with the required pressure. Air compressors are also used for inflating sports balls, inflatable toys, and other similar items.

4. Operating HVAC Systems: Air compressors play a crucial role in the operation of heating, ventilation, and air conditioning (HVAC) systems. They provide compressed air for controlling and actuating dampers, valves, and actuators in HVAC systems, enabling precise regulation of air flow and temperature.

5. Assisting in Industrial Processes: Compressed air is utilized in various industrial processes. It can be used for air blow-off applications, cleaning and drying parts, powering air-operated machinery, and controlling pneumatic systems. Air compressors provide a reliable and efficient source of compressed air that can be tailored to meet the specific requirements of different industrial applications.

6. Supporting Scuba Diving and Breathing Systems: In scuba diving and other breathing systems, air compressors are responsible for filling diving tanks and supplying breathable air to divers. These compressors are designed to meet strict safety standards and deliver compressed air that is free from contaminants.

Overall, the purpose of an air compressor is to provide a versatile source of compressed air for powering tools, supplying clean air for various applications, inflating tires and sports equipment, supporting industrial processes, and facilitating breathing systems in specific contexts.

China OEM Low Noise 70kw 100HP Permanent Magnet VSD Frequency Conversion Screw Air Compressor mini air compressor
editor by CX 2023-12-04

China supplier Industrial Electric Permanent Magnet Synchronous Variable Frequency Converter Drive Pm VSD/VFD Inverter Rotary Double Screw Air Compressor in Shanghai China portable air compressor

Product Description

Technical data

Model	Power (kw)	Pressure (bar)	Air flow (m³/min)	Noise	Stage	Exit pipe diameter	Boundary dimension			Total Weight (kg)
							Length Width Height(mm)
WZS-10EVA	7.5	8	1.0	60±2	single stage	3/4	800	750	1000	200
		10	0.8
WZS-15EVA	11	8	1.8	62±2	single stage	1	1200	850	1300	260
		10	1.6
WZS-20EVA	15	8	2.2	63±2	single stage	1	1200	850	1300	380
		10	1.8
WZS-30EVA	22	8	3.8	66±2	single stage	2.75	1200	800	1300	420
		10	3.0				1380	850	1150	460
WZS-40EVA	30	8	5.0	68±2	single stage	2.75	1380	850	1150	600
		10	4.4
WZS-50EVA	37	8	6.2	66±2	single stage	2.75	1300	1000	1450	700
		10	5.4				1600	1000	1550	750
WZS-60EVA	45	8	8.0	68±2	single stage	2.75	1600	1000	1370	780
		10	6.8
WZS-75EVA	55	8	10.5	69±2	single stage	2.75	1800	1270	1550	1350
		10	8.5
WZS-100EVA	75	8	13.2	70±2	single stage	2.75	2050	1270	1550	1470
		10	11.6
WZS-125EVA	90	8	16.0	70±2	single stage	2.75	2150	1100	1500	1750
		10	14.0
WZS-150EVA	110	8	20.5	71±2	single stage	DN65	2750	1750	1900	2600
		10	17.3
WZS-180EVA	132	8	22.0	72±2	single stage	DN80	2750	1750	1900	2880
		10	20.1
WZS-220EVA	160	8	27.0	75±2	single stage	DN100	2950	1800	1850	3200
		10	24.5
WZS-250EVA	185	8	30.4	85±2	single stage	DN100	3000	2000	2100	3500
		10	28.6
WZS-270EVA	200	8	33.5	85±2	single stage	DN100	3000	2000	2100	3650
		10	31.0
WZS-300EVA	220	8	40.5	85±2	single stage	DN125	3200	2100	2450	3800
		10	36.5
WZS-340EVA	250	8	43.5	85±2	single stage	DN125	3200	2100	2450	4200
		10	39.5

Wan CHINAMFG Certification

Wan CHINAMFG Exhibition

FAQ

1. OEM/ODM, or customer’ s logo printed is available?

Yes, OEM/ODM, customer’s logo is welcomed.

2. Delivery date?
Usually 5-25 working days after receiving deposit, specific delivery date based on order quantity.

3. What’s your payment terms?

Regularly doing 30% deposit and 70% balance by T/T, Western Union, Paypal, other payment terms also can be discussed based on our cooperation.

4. How to control your quality?

We have professional QC team, control the quality during the mass production and inspect the products before shipping.

5. If we don’ t have shipping forwarder in China , would you do this for us?

We can offer you best shipping line to ensure you can get the goods timely at best price.

6. I never come to China before , can you be my guide in China?

Sure , I’m glad to be your guide because our company directly located in ZheJiang , where is the most famous city in China, if you want to come China then we are happy to provide you one-stop service, such as booking ticket, picking up at the airport, booking hotel, accompany visiting factory. It gonna make you an unforgettable memory.

MARKETING NETWORK

After-sales Service:	Video Technical Support
Warranty:	Unit 1 Year, Air End 2 Years
Lubrication Style:	Oil-less

Customization:	Available \|

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost: Estimated freight per unit.	about shipping cost and estimated delivery time.

Payment Method:
	Initial Payment Full Payment

Currency:	US$

Return&refunds:	You can apply for a refund up to 30 days after receipt of the products.

air compressor

How does variable speed drive technology improve air compressor efficiency?

Variable Speed Drive (VSD) technology improves air compressor efficiency by allowing the compressor to adjust its motor speed to match the compressed air demand. This technology offers several benefits that contribute to energy savings and enhanced overall system efficiency. Here’s how VSD technology improves air compressor efficiency:

1. Matching Air Demand:

Air compressors equipped with VSD technology can vary the motor speed to precisely match the required compressed air output. Traditional fixed-speed compressors operate at a constant speed regardless of the actual demand, leading to energy wastage during periods of lower air demand. VSD compressors, on the other hand, ramp up or down the motor speed to deliver the necessary amount of compressed air, ensuring optimal energy utilization.

2. Reduced Unloaded Running Time:

Fixed-speed compressors often run unloaded during periods of low demand, where they continue to consume energy without producing compressed air. VSD technology eliminates or significantly reduces this unloaded running time by adjusting the motor speed to closely follow the air demand. As a result, VSD compressors minimize energy wastage during idle periods, leading to improved efficiency.

3. Soft Starting:

Traditional fixed-speed compressors experience high inrush currents during startup, which can strain the electrical system and cause voltage dips. VSD compressors utilize soft starting capabilities, gradually ramping up the motor speed instead of instantly reaching full speed. This soft starting feature reduces mechanical and electrical stress, ensuring a smooth and controlled startup, and minimizing energy spikes.

4. Energy Savings at Partial Load:

In many applications, compressed air demand varies throughout the day or during different production cycles. VSD compressors excel in such scenarios by operating at lower speeds during periods of lower demand. Since power consumption is proportional to motor speed, running the compressor at reduced speeds significantly reduces energy consumption compared to fixed-speed compressors that operate at a constant speed regardless of the demand.

5. Elimination of On/Off Cycling:

Fixed-speed compressors often use on/off cycling to adjust the compressed air output. This cycling can result in frequent starts and stops, which consume more energy and cause mechanical wear. VSD compressors eliminate the need for on/off cycling by continuously adjusting the motor speed to meet the demand. By operating at a consistent speed within the required range, VSD compressors minimize energy losses associated with frequent cycling.

6. Enhanced System Control:

VSD compressors offer advanced control capabilities, allowing for precise monitoring and adjustment of the compressed air system. These systems can integrate with sensors and control algorithms to maintain optimal system pressure, minimize pressure fluctuations, and prevent excessive energy consumption. The ability to fine-tune the compressor’s output based on real-time demand contributes to improved overall system efficiency.

By utilizing variable speed drive technology, air compressors can achieve significant energy savings, reduce operational costs, and enhance their environmental sustainability by minimizing energy wastage and optimizing efficiency.

air compressor

What safety precautions should be taken when working with compressed air?

Working with compressed air requires adherence to certain safety precautions to prevent accidents and ensure the well-being of individuals involved. Here are some important safety measures to consider:

1. Personal Protective Equipment (PPE):

Wear appropriate PPE, including safety goggles or a face shield to protect eyes from flying debris or particles, hearing protection to reduce noise exposure, and gloves to safeguard hands from potential hazards.

2. Compressed Air Storage:

Avoid storing compressed air in containers that are not designed for this purpose, such as soda bottles or makeshift containers. Use approved and properly labeled air storage tanks or cylinders that can handle the pressure and are regularly inspected and maintained.

3. Pressure Regulation:

Ensure that the air pressure is regulated to a safe level suitable for the equipment and tools being used. High-pressure air streams can cause serious injuries, so it is important to follow the manufacturer’s recommendations and never exceed the maximum allowable pressure.

4. Air Hose Inspection:

Regularly inspect air hoses for signs of damage, such as cuts, abrasions, or leaks. Replace damaged hoses immediately to prevent potential accidents or loss of pressure.

5. Air Blowguns:

Exercise caution when using air blowguns. Never direct compressed air towards yourself or others, as it can cause eye injuries, hearing damage, or dislodge particles that may be harmful if inhaled. Always point blowguns away from people or any sensitive equipment or materials.

6. Air Tool Safety:

Follow proper operating procedures for pneumatic tools. Ensure that tools are in good working condition, and inspect them before each use. Use the appropriate accessories, such as safety guards or shields, to prevent accidental contact with moving parts.

7. Air Compressor Maintenance:

Maintain air compressors according to the manufacturer’s guidelines. Regularly check for leaks, clean or replace filters, and drain moisture from the system. Proper maintenance ensures the safe and efficient operation of the compressor.

8. Training and Education:

Provide adequate training and education to individuals working with compressed air. Ensure they understand the potential hazards, safe operating procedures, and emergency protocols. Encourage open communication regarding safety concerns and implement a culture of safety in the workplace.

9. Lockout/Tagout:

When performing maintenance or repairs on compressed air systems, follow lockout/tagout procedures to isolate the equipment from energy sources and prevent accidental startup. This ensures the safety of the individuals working on the system.

10. Proper Ventilation:

Ensure proper ventilation in enclosed areas where compressed air is used. Compressed air can displace oxygen, leading to a potential risk of asphyxiation. Adequate ventilation helps maintain a safe breathing environment.

By adhering to these safety precautions, individuals can minimize the risks associated with working with compressed air and create a safer work environment.

air compressor

How do you choose the right size of air compressor for your needs?

Choosing the right size of air compressor is essential to ensure optimal performance and efficiency for your specific needs. Here are some factors to consider when selecting the appropriate size:

1. Air Demand: Determine the air demand requirements of your applications. Calculate the total CFM (Cubic Feet per Minute) needed by considering the air consumption of all the pneumatic tools and equipment that will be operated simultaneously. Choose an air compressor with a CFM rating that meets or exceeds this total demand.

2. Pressure Requirements: Consider the required operating pressure for your applications. Check the PSI (Pounds per Square Inch) rating of the tools and equipment you will be using. Ensure that the air compressor you choose can deliver the necessary pressure consistently.

3. Duty Cycle: Evaluate the duty cycle of the air compressor. The duty cycle represents the percentage of time the compressor can operate within a given time period without overheating or experiencing performance issues. If you require continuous or heavy-duty operation, choose a compressor with a higher duty cycle.

4. Power Source: Determine the available power source at your location. Air compressors can be powered by electricity or gasoline engines. Ensure that the chosen compressor matches the available power supply and consider factors such as voltage, phase, and fuel requirements.

5. Portability: Assess the portability requirements of your applications. If you need to move the air compressor frequently or use it in different locations, consider a portable or wheeled compressor that is easy to transport.

6. Space and Noise Constraints: Consider the available space for installation and the noise restrictions in your working environment. Choose an air compressor that fits within the allocated space and meets any noise regulations or requirements.

7. Future Expansion: Anticipate any potential future expansions or increases in air demand. If you expect your air demand to grow over time, it may be wise to choose a slightly larger compressor to accommodate future needs and avoid the need for premature replacement.

8. Budget: Consider your budgetary constraints. Compare the prices of different air compressor models while ensuring that the chosen compressor meets your specific requirements. Keep in mind that investing in a higher-quality compressor may result in better performance, durability, and long-term cost savings.

By considering these factors and evaluating your specific needs, you can choose the right size of air compressor that will meet your air demand, pressure requirements, and operational preferences, ultimately ensuring efficient and reliable performance.

China supplier Industrial Electric Permanent Magnet Synchronous Variable Frequency Converter Drive Pm VSD/VFD Inverter Rotary Double Screw Air Compressor in Shanghai China portable air compressor
editor by CX 2023-11-09

China high quality Ga45 VSD Ipm 45kw 60HP 181psig 12.5bar 2.41-6.61m3/Min Variable Speed Drive CHINAMFG Rotary Permanent Magnet Screw Air Compressors mini air compressor

Product Description

We are authorized distributer of atlas copco, we could provide whole product line of
Atlas Copco air compressors , spare parts and consumables. we are also
certified supplier by international authoritative certification
organizations.

Kindly advise your technical requirements, we will recommend suitable
compressed air system and spare parts for you .

We can provide CHINAMFG One-Stop Service,and efficient energy – saving solutions for you .

Products Description

GA 7-75 VSD iPM series Oil-Injected screw air compressors,If you need more professional technical

Industrial equipment, printing service, pipelines,power plants, oil&gas, oil refinery, coating, painting,
plastics, steel industry, rubber, mechanical, blow molding, color sorter machine, shipyard, sandblasting,
metallurg,etc.

Different industries correspond to different air compressors, kindly please send me your application
areas and specific conditions, then will recommend the most suitable products for you .

Shipping
We can provide CHINAMFG standard packaging or OEM packaging.

1 Q: How about the quality of products ?

A: We are authorized distributer of Atlas Copco. Don’t worry the quality and service.

2 Q: How long is your delivery lead time ?

A: If there is stock, the lead time is about 3 working days after we get the payment, if need to
be produced, it depends.

3 Q: How about your overseas after-sale service?

A: (1)Provide customers with intallation and commissioning online instructions.

(2)Worldwide agents and sfter service available.

4 Q: Can you accept OEM&ODM orders?

A: Yes, we have professional design team, OEM&ODM orders are highly welcomed.

Warranty:	1 Year
Lubrication Style:	Lubricated
Cooling System:	Air Cooling
Power Source:	AC Power
Cylinder Position:	Vertical
Structure Type:	Closed Type

Customization:	Available \|

air compressor

Can air compressors be used for cleaning and blowing dust?

Yes, air compressors can be effectively used for cleaning and blowing dust in various applications. Here’s how air compressors are utilized for these purposes:

1. Cleaning Machinery and Equipment:

2. Dusting Surfaces:

3. Cleaning HVAC Systems:

4. Blowing Dust in Workshops:

5. Cleaning Electronics and Computer Equipment:

6. Industrial Cleaning Applications:

Overall, air compressors provide a versatile and effective solution for cleaning and blowing dust in various applications, offering a convenient alternative to traditional cleaning methods.

air compressor

What safety precautions should be taken when working with compressed air?

1. Personal Protective Equipment (PPE):

2. Compressed Air Storage:

3. Pressure Regulation:

4. Air Hose Inspection:

Regularly inspect air hoses for signs of damage, such as cuts, abrasions, or leaks. Replace damaged hoses immediately to prevent potential accidents or loss of pressure.

5. Air Blowguns:

6. Air Tool Safety:

7. Air Compressor Maintenance:

8. Training and Education:

9. Lockout/Tagout:

10. Proper Ventilation:

By adhering to these safety precautions, individuals can minimize the risks associated with working with compressed air and create a safer work environment.

air compressor

What is the difference between a piston and rotary screw compressor?

Piston compressors and rotary screw compressors are two common types of air compressors with distinct differences in their design and operation. Here’s a detailed explanation of the differences between these two compressor types:

1. Operating Principle:

Piston Compressors: Piston compressors, also known as reciprocating compressors, use one or more pistons driven by a crankshaft to compress air. The piston moves up and down within a cylinder, creating a vacuum during the intake stroke and compressing the air during the compression stroke.
Rotary Screw Compressors: Rotary screw compressors utilize two intermeshing screws (rotors) to compress air. As the male and female screws rotate, the air is trapped between them and gradually compressed as it moves along the screw threads.

2. Compression Method:

Piston Compressors: Piston compressors achieve compression through a positive displacement process. The air is drawn into the cylinder and compressed as the piston moves back and forth. The compression is intermittent, occurring in discrete cycles.
Rotary Screw Compressors: Rotary screw compressors also employ a positive displacement method. The compression is continuous as the rotating screws create a continuous flow of air and compress it gradually as it moves along the screw threads.

3. Efficiency:

Piston Compressors: Piston compressors are known for their high efficiency at lower flow rates and higher pressures. They are well-suited for applications that require intermittent or variable air demand.
Rotary Screw Compressors: Rotary screw compressors are highly efficient for continuous operation and are designed to handle higher flow rates. They are often used in applications with a constant or steady air demand.

4. Noise Level:

Piston Compressors: Piston compressors tend to generate more noise during operation due to the reciprocating motion of the pistons and valves.
Rotary Screw Compressors: Rotary screw compressors are generally quieter in operation compared to piston compressors. The smooth rotation of the screws contributes to reduced noise levels.

5. Maintenance:

Piston Compressors: Piston compressors typically require more frequent maintenance due to the higher number of moving parts, such as pistons, valves, and rings.
Rotary Screw Compressors: Rotary screw compressors have fewer moving parts, resulting in lower maintenance requirements. They often have longer service intervals and can operate continuously for extended periods without significant maintenance.

6. Size and Portability:

Piston Compressors: Piston compressors are available in both smaller portable models and larger stationary units. Portable piston compressors are commonly used in construction, automotive, and DIY applications.
Rotary Screw Compressors: Rotary screw compressors are typically larger and more suitable for stationary installations in industrial and commercial settings. They are less commonly used in portable applications.

These are some of the key differences between piston compressors and rotary screw compressors. The choice between the two depends on factors such as required flow rate, pressure, duty cycle, efficiency, noise level, maintenance needs, and specific application requirements.

China high quality Ga45 VSD Ipm 45kw 60HP 181psig 12.5bar 2.41-6.61m3/Min Variable Speed Drive CHINAMFG Rotary Permanent Magnet Screw Air Compressors mini air compressor
editor by CX 2023-10-26